Resources

OSHA's preliminary FY2026 Top 10 puts 1926.501 first again with 4,041 violations. The full list, what 1926.501 and 1926.503 require, and why the ranking never moves.

ANSI/ISEA Z89.1-2026 adds optional Type I+ and Type II+ head protection classes built around chin strap and retention testing. What changed, what did not, and a five minute crew check.

A Brooklyn indictment over allegedly fake OSHA and site safety cards exposes a gap most contractors have: they verify that the card exists, never that the class did. Here is how to actually check.

Two scaffold incidents on September 7, 2026 both happened while the structure was being built or taken apart. What 1926.451(f)(7) and 1926.454(b) require in that window, and a checklist for the crew.

A Michigan worker slid into a sewer excavation when the trench wall gave way beside a trench box. OSHA 1926.651(k)(1) covers the adjacent areas, and almost nobody inspects them.

IPAF's 2026 global report puts electrocution ahead of falls from the platform and overturns. OSHA 1926.453 has no clearance table, and that is where crews get caught.

There is no general severe weather standard in Part 1926, which is why most jobsite weather plans are one unusable paragraph. Here is what OSHA does require and what a workable plan contains.

The 2027 Texas UTP headline is $138 billion. Only $95 billion is project money, down 6.5 percent from the 2026 plan. Here is what a tighter letting schedule does to bidding and to safety budgets.

29 CFR 1926.106 is four paragraphs long, sets no depth threshold, and applies to far more construction sites than the crews on them realize. Here is what it requires and how to make the call.

A fatal trench collapse in Stockton killed two workers in a ten foot excavation in August 2026. Here is what the excavation standard requires, what the data shows, and a toolbox talk you can run tomorrow.

The industry is short roughly 439,000 workers while more than 400 data centers are under development. A 30 percent wage premium does not create experience. It moves it, and it moves it off your job.

Fall protection has topped OSHA's citation list for 15 straight years. Here's what the 2024 fall data shows, plus a jobsite checklist to keep your crew off the ground.

A 22-year-old worker died when a crane jib collapsed at an Indiana wind farm. Here's what OSHA's crane standard requires before your next extension.

A 23-year-old worker died and two more were injured in three separate trench collapses across Southeast Michigan within 48 hours. Here's what protective systems should have been in place.

The federal heat standard is stalled, but OSHA just renewed heat inspections for five more years. What changed in April 2026 and what your jobsite heat program needs before summer peaks.

Heat is the leading weather-related killer of workers in the United States. Most sites have water and shade. Most sites still get it wrong. Here's what the data says about heat illness on construction sites and what an effective prevention program actually looks like.

Falls, struck-by incidents, electrocutions, and caught-in/between accidents account for 65% of all construction fatalities. We've known about these hazards for decades. Workers are still dying from them every week. Here's why the Fatal Four keep winning and what actually has to change.

May 4 through 8 is the 13th annual National Safety Stand-Down to Prevent Falls in Construction. Falls are still the leading cause of construction fatalities. Here's what the Stand-Down is actually for and how to make yours count.

National Safety Stand-Down to Prevent Falls is May 4-8, 2026. What a good one looks like on a real construction site and what a wasted one

A broken grinder or a failed hydraulic system doesn't announce itself. It waits. Pre-use inspections are your last line of defense before equipment failure becomes a fatality. Every year, workers are seriously injured or killed by equipment that someone had already inspected and passed. Not because inspections don't work. Because they were skipped, rushed, or treated like a formality. On a busy jobsite, it's easy to assume the tool you grabbed yesterday is still good today. T